New Engine Plaque

[GFWilliams]

Just wanted to say thank you to @alias23 for this new badge for the engine.   Finishes off my engine bay nicely!

[alias23]

Pleasure! Thanks @GFWilliams for supporting this little project right from the start!!

After quite a few requests I'm looking to kick off an initial production run (in small numbers). If anyone would like to get in on the run please give me a shout. The plates are anodised in black, then CNC machined to design, for the eagle eyed among you note the slightly bevelled edging - My aim was to do a proper job to replace the cheap plastic you get from factory.

Im genuinely chuffed with the end result, never done anything like this before, and blessed to have folks around me who can help put my ideas into action! 

[C8RKH]

Yes please, they are truly epic looking. Thank you.

[Mattmahope]

I would love one but not sure how to mount on my silver supercharger?

[alias23]

33 minutes ago, Mattmahope said:

I would love one but not sure how to mount on my silver supercharger?

I’m afraid it won’t fit unless you have the original charger with the bolt fixings.

[race]

mp Alias

for one if possible ,regards

 

[geartox]

how much is it ?

 

[alias23]

1 hour ago, race said:

mp Alias

for one if possible ,regards

 

Just messaged you back thank you.

25 minutes ago, geartox said:

how much is it ?

 

£50 inc postage

[geartox]

pm sent.

 

[alias23]

1 hour ago, geartox said:

pm sent.

 

and responded

Thanks for your support @geartox

[Mark030358]

@alias23 I’ll have one too please mate...

thanks

[alias23]

57 minutes ago, Mark030358 said:

@alias23 I’ll have one too please mate...

thanks

Do you have the bolt hole fixings on the charger? I didn't think the 380 did as the original V6 does which has the plastic engine badge.

One 380 owner has asked me to make him one with no bolt holes which he is going to then use metal epoxy to glue it direct to the charger. So there's an option for those that don't have the original fixings on top of the charger. That said all done at owners risk as I've not tested this as an idea. Let me know either way Mark

[Karls]

Please put me down for one. Thanks.

[MrP_]

another one for me please, PM Sent

[alias23]

@Karls @MrP_ from memory aren't you both Exige 350... if so do you have the fixings in the charger or are you going to use metal epoxy as per my previous post? If the later do you want the holes in the plaque or no holes? Just pinged you both PMs so let me know by reply. Cheers

[MrP_]

10 minutes ago, alias23 said:

@Karls @MrP_ from memory aren't you both Exige 350... if so do you have the fixings in the charger or are you going to use metal epoxy as per my previous post? If the later do you want the holes in the plaque or no holes? Just pinged you both PMs so let me know by reply. Cheers

With holes, thankfully I was after everyone complained about the silver chargers so I got black (before they went back again when the 410 came out) 😀 Replied to PM

[alias23]

4 hours ago, Karls said:

Please put me down for one. Thanks.

Let me know if you need no holes or like @MrP_ happy with the fixings.

[Karls]

34 minutes ago, alias23 said:

Let me know if you need no holes or like @MrP_ happy with the fixings.

With holes please - PM sent

[Mark030358]

7 hours ago, alias23 said:

Do you have the bolt hole fixings on the charger? I didn't think the 380 did as the original V6 does which has the plastic engine badge.

One 380 owner has asked me to make him one with no bolt holes which he is going to then use metal epoxy to glue it direct to the charger. So there's an option for those that don't have the original fixings on top of the charger. That said all done at owners risk as I've not tested this as an idea. Let me know either way Mark

Hi Imran,

With holes please, it's not going on the charger  

Can you pm me your paypal account no. and the cost incl. p&p

They look proper quality!!

thanks

[alias23]

3 minutes ago, Mark030358 said:

Hi Imran,

With holes please, it's not going on the charger  

Can you pm me your paypal account no. and the cost incl. p&p

They look proper quality!!

thanks

Details sent to your PM thanks 

[Forkhandles]

They look stunning, could I have one please.

send me you PayPal details and I will send the payment over,

manythanks

[Steve V8]

You Evorites and Exigers need to share the bling...

Ordered for Esprit engine bay..👍👍👍

 

[Julian73]

On 03/02/2019 at 00:18, Mattmahope said:

I would love one but not sure how to mount on my silver supercharger?

RTV and cut down hex heads and glue those with RTV also.  This worked on my 2012 car

 

[geartox]

On 02/02/2019 at 15:02, GFWilliams said:

Just wanted to say thank you to @alias23 for this new badge for the engine.   Finishes off my engine bay nicely!

 

 

can you explain us how do keep an engine bay so clean and nice ? 🤔😋

 

[Dan.G]

Bugger, if everyone else is getting one...

Oh wait, I can't, I have a cheap supercharger