peter1707

So some S2's have this design wheel are they then different dimensions. WOw

HI , Would these fit a Elite s2 cheers Pete

Yes sorry Collect from Ghent in Belgium delivery to Reading

Hi Does anyone know of a flatback truck for hire as I need a car collected

HI , I'm looking to buy a Lotus Elite all conditions considered. Cheers Pete

Lovely looking Elite does anyone know anything about the car, all advise would be welcome Cheers Pete

I have had the fuel pump not working recently and it soon because obvious , that the mounting was loose or actually the foam that surrounds the pump has lost its give. So I'm guessing the 12v wires start to loose connection as it moves. It seems an impossible task trying to tighten it up as the bolts are very difficult to access, but I'm sure I will manage. does anyone use a better system that existing brackets as it seems like this could be a reoccurring problem

Thanks for all the suggestion's I have looked and had a go at all of them , but I now think its actually the motor, because although I did test it, by letting just run freely, as soon as It has any load on it eg I grab the end with my hand, I can easily stop it, which does not seem right.?? It looks fine no burning or obvious signs of damage , I assume its the magnets that go or the brush's start to not work. Anyway can they be repaired of just buy a new one, Lotus bits didn't have one any one else you know? Its a Delco motor cheers Pete

Ok cheers, how do you get to them , they seem tucked away between the door skins

Hi, I have a 1989 Excel, and the passenger window keeps getting stuck , it slows down speeds up and it looks like the battery is running out, which its not. So I have had a look and removed the electric motor and that runs fine when not connected to anything, I have sprayed silicone spray on the runners . Moving the widow up and down by hand it does feel tight in places but its difficult to know what is correct. I'm guessing its therefore either the gearbox( if that's the correct word ) or the whole of the mechanism , the steel work is somehow bent or distorted. I would welcome any advise or experience of this problem. cheers Pete

I must have knocked something as the left had side fixing has come away from the spoiler , and it has now dropped 20mm . it looks like the whole needs to be taken off and the bolt bonded back on, does anyone have any advise before I start Cheers Pete

Hi, thanks, yes mine are the same 55 to 58, but it does run too rich and it smells and will be a problem at the MOT. I have also bought that book it seems excellent, but the bit I worry about is actually changing things for the worst and damaging the engine by going too learn , do people use stuff like colourtune to check the idle mixture, I may just change the jets and sniff .

I have a1990 excel and it runs very rich, the previous owner had new jets fitted to get rid of a flat spot. However I would like to refit the old original jets to help get rid of the smell and get the engine running correctly. Will I have to reset and adjust the mixture afterwards, or can I just swap the jets ? Any advise on carbs would be welcome

Ok thanks for the advise it was a knacked relay, its a tight fit under there!

Ok cheers, are they in with the fuses ?

Hi I have just come back home and noticed my headlights have popped down just lovely, but have remained on, shinning brightly. does anyone know where to start ? cheers Pete

I was thinking of doing an engine rebuild at some piont in my2.2 excel, and it got my thinking of what other engine options have people used, I assume a toyota unit would be a great choice, fits gearbox and they make great engines

Ok cheers I made a wooden ramp in the end very successful, only to find a very dodgy sump plug washer , completely the wrong size and the excel washers is too big for any local motor shop to stock.

very nice , but which one is helping show off the other

With the car being pretty low , what is the best /safest method of getting the car up enough to work on oil change etc.

Ok thanks, so the spare oil in the boot was Helix 10w40, seems completely wrong

Hi I have only recently bought a very nice 1990 excel , very pleased. but she is a bit smelly, it seems like exhaust coming inside the cabin and I think she s running to Rich, starts perfectly with no choke. So I have had a good look while she's been up on ramps, no trace of leaking exhaust. So I 'm thinking is the running rich and a bit of an exhaust smell connected. I know the carbs have been re jetted so I may think about changing them back to what was in them before. So any advise welcome Pete

So what oil in an Engine that hasn't had a rebuild I assume there are better options than what lotus printed in the manual 30 years ago

This might be a stupid question but since the sizes are different to the cars original spec, what pressure do you inflate them to. Also since I am a new owner what oil does everone use again since there is better stuff than in the 80s

Can anyone recommend a car cover for use outside on an excel.